ON A GENERALIZED INPUT SHAPING FOR RESIDUAL VIBRATION SUPPRESSION IN FLEXIBLE SYSTEM WITH NONLINEAR SPRING AND DAMPER
DOI:
https://doi.org/10.11113/aej.v15.21866Keywords:
Residual vibration control, input shaping, flexible systems, Duffing nonlinearity, nonlinear systemsAbstract
Suppression of residual vibrations in position control of flexible systems is a challenging problem, especially in the presence of high nonlinearities or diverse operating points. Input shaping, a technique for designing shaped commands to minimize system residual vibration during point-to-point movements, is crucial. Traditional input shapers like zero-vibration and zero-vibration-and-derivative shapers, designed based on the superposition principle, perform well for linear systems but have limitations in highly nonlinear systems. This paper revisits nonlinear input shapers, including three-impulse and robust shapers, providing a comprehensive energy-based analysis. Additionally, a novel fast three-impulse shaper is proposed to improve the time-delay of traditional input shapers. The amplitudes and time locations of all designed shapers are proven in the same closed-form solution for the undamped case, suitable for analyzing sensitivity to variations in plant parameters. Demonstrations on a two-mass flexible system with nonlinear spring and damper show that the proposed fast-three shaper outperforms the two-impulse shaper in robustness, with similar performance in rise time. However, robust shapers, while slower, exhibit superior robustness as increasing impulse numbers decrease residual total energy. The effect of nonlinear damping force is demonstrated in simulations, providing suggestions for designing robust shapers for damped flexible systems.
References
Montonen, J. H., Nevaranta, N., Niemelä, M., & Lindh, T. 2022. Comparison of extrainsensitive input shaping and swing-angle-estimation-based slew control approaches for a tower crane. Applied Sciences. 12(12): 5945. DOI: https://doi.org/10.3390/app12125945
Thomsen, D. K., Søe-Knudsen, R., Balling, O., & Zhang, X. 2021. Vibration control of industrial robot arms by multi-mode time-varying input shaping. Mechanism and Machine Theory. 155: 104072. DOI: https://doi.org/10.1016/j.mechmachtheory.2020.104072
Wang, W., Hu, C., Zhou, K., & Wang, Z. 2023. Time parameter mapping and contour error precompensation for multiaxis input shaping. IEEE Transaction on Industrial Informatics. 19(3): 2640-51. DOI: 10.1109/TII.2022.3158960
Ahumada, C. & Wheeler, P. 2021. Evaluation of input-shaping control robustness for the reduction of torsional vibrations. IEEE Transactions on Industry Applications. 57(5): 5028-38. DOI: 10.1109/TIA.2021.3087673
Nguyen, M. N., Tran, D. T., & Ahn, K. K. 2018. Robust position and vibration control of an electrohydraulic series elastic manipulator against disturbance generated by a variable stiffness actuator. Mechatronics. 52: 22-35. DOI: 10.1016/j.mechatronics. 2018.04.004
Ameura, H., Moal, P. L., Bourbona, G., Vuillemin, C., & Sworowski, M. 2022. Suppressing residual vibrations in comb-drive electrostatic actuators: a command shaping technique adapted to nomadic applications. Sensors and Actuators A: Physical. 334: 113366. DOI: https://doi.org/10.1016/j.sna.2022.113366
Meng, L., Huang, Y., Wang, X., Li, F., & Li, H. 2020. Design and experimental validation of a robust input shaper for eliminating vibration in dielectric elastomer actuators under varying applied voltage. Sensors and Actuators A: Physical. 316: 112392. DOI: https://doi.org/10.1016/j.sna.2020.112392
Smith, O. J. M. 1957. Posicast control of damped oscillatory systems. In Proceedings of the IRE. 1249-55. DOI: 10.1109/JRPROC.1957.278530
Singer, N. C. & Seering, W. C. 1990. Preshaping command inputs to reduce system vibration. Journal of Dynamic Systems, Measurement, and Control. 112: 76-82. DOI: 10.1115/1.2894142
Chatlatanagulchai, W., Damyot, S., & Intarawirat, P. 2017. Switching ZVDk input shaper for flexible closed-loop system with saturation. In Proceedings of the American Control Conference. 4492-7.
Mohammed, A., Alghanim, K., & Andani, M. T. 2021. A robust input shaper for trajectory control of overhead cranes with non-zero initial states. International Journal of Dynamics and Control. 9(5): 230-9. DOI: https://doi.org/10.1007/s40435-020-00631-0
Moonmanngmee, I., Juyploy, P., & Chatlatanagulchai, W. 2023. Input shaping for flexible systems with non-zero initial conditions. Trends in Sciences. 20(12). DOI: 10. 48048/ tis.2024.7193.
Newman, D., Hong, S. W., & Vaughan, J. E. 2018. The design of input shapers which eliminate nonzero initial conditions. Journal of Dynamic Systems, Measurement, and Control. 140(10): 101005. DOI: https://doi.org/10.1115/1.4039668
Wahrburg, A., Jurvanen, J., Niemelä, M., & Holmberg, M. 2022. Input shaping for non-zero initial conditions and arbitrary input signals with an application to overhead crane control. In Proceedings of the IEEE 17th International Conference on Advanced Motion Control (AMC). 36-41. DOI: 10.1109/AMC51637.2022.9729261
Thomsen, D. K., Søe-Knudsen, R., Brandt, D., Balling, O., & Zhang, X. 2019. Smooth online time-varying input shaping with fractional delay FIR filtering. Control Engineering Practice. 88(7): 21-37. DOI: 10.1016/j.conengprac. 2019.04.003
Arabasi, S. & Masoud, Z. 2017. Simultaneous travel and hoist maneuver input shaping control using frequency modulation. Shock and Vibration. 2017(6): 5703820. DOI: https://doi.org/10.1155/2017/5703820
Arabasi, S. & Masoud, Z. 2022. Frequency-modulation input-shaping strategy for double-pendulum overhead cranes undergoing simultaneous hoist and travel maneuvers. IEEE Access. 10(4): 44954-63. DOI: 10.1109/ACCESS.2022.3170099
Chen, K. S., Yang, T. S., Ou, K. S., & Yin, J. F. 2009. Design of command shapers for residual vibration suppression in Duffing nonlinear systems. Mechatronics. 19(3): 184-198. DOI: 10.1016/j.mechatronics.2008. 08.005
Chatlatanagulchai, W., Moonmanngmee, I., & Intarawirat, P. 2018. Input shaping for flexible system with nonlinear spring and damper. In the ASME 2017 International Mechanical Engineering Congress and Exposition.
Tang W., Ma, R., Wang, W., & Gao, H. 2023. Optimization-based
