STRESS-STRAIN RELATIONSHIPS OF COMPOSITE FOAMED CONCRETE PANEL WITH DIFFERENT NUMBER OF SHEAR CONNECTORS UNDER COMPRESSION

Authors

  • M. A. Othuman Mydin School of Housing, Building and Planning, Universiti Sains Malaysia, 11800, Penang, Malaysia
  • N. Utaberta Architecture Department, Faculty of Design and Architecture, Universiti Putra Malaysia, Malaysia
  • M. Y. Mohd Yusof Department of Landscape Architecture, Faculty Design and Architecture, Universiti Putra Malaysia, Malaysia
  • N. A. Amirudin School of Housing, Building and Planning, Universiti Sains Malaysia, 11800, Penang, Malaysia

DOI:

https://doi.org/10.11113/jt.v75.4955

Keywords:

Lightweight foam concrete, sandwich panel, axial load, stress-strain

Abstract

The present of the shear connectors with the sandwich composite foamed concrete panel system is to increase the strength of the panel. Therefore the objectives of experiment on effects of the shear connectors spacing is to determine the influence of shear connectors spacing on the axial stress-strain curve, to observe the failure mode sandwich composite foamed concrete panel system with different shear connectors spacing, and to establish ultimate load carrying capacity of different shear connectors spacing. In this study, there are four samples of shear connectors spacing which are 5, 7, 9 and 13 to composited foamed concrete with density of 1400 kg/m3 and 700 kg/m3. This study has showed the enhancement of ultimate compressive strength with increasing numbers of mechanical connectors. The failure of mode observed proved that sandwich panel failures decreasing with enhancement numbers of mechanical connectors, thus sandwich panels can sustained ultimate load carrying capacity.  

References

PCI Committee On Pre-Cast Concrete Sandwich Wall Panels. 1997. State of the Art of Precast/Prestresses Sandwich Wall Panels. 42(2): 92-133.

Einea, A., Salmon, D. C., Tandros, M. K., Culp, T. 1994. A New Structurally and Thermally Efficient Precast Sandwich Panel System. PCI J. 39(4): 90-101.

E. Losch. 2005. Precast/Prestressed Concrete Sandwich Walls. Structure Magazine. April:16-20.

A. Benayoune, A. A. Abdul Samad, D. N. Trikha, A. A. Abang Ali, S. H. M. Ellinna. 2008. Flexural Behavior of Pre-cast Concrete Sandwich Composite Panel–Experimental and Theoretical Investigations. Construction and Building Materials. 22: 580-592.

Wan Abdullah Wan Alwi. 2009. Strength and Durability of Lightweight Foam Concrete as Structural Material. PhD Thesis. Universiti Sains Malaysia. 5-354.

M. A. Othuman Mydin. 2015. Effect of Silica Fume and Wood Ash Additions on Flexural and Splitting Tensile Strength of Lightweight Foamed Concrete. Jurnal Teknologi. 74(1): 125-129.

Soleimanzadeh, S., M. A. Othuman Mydin. 2013. Influence of High Temperatures on Flexural Strength of Foamed Concrete Containing Fly Ash and Polypropylene Fiber. International Journal of Engineering. 26(1): 365-374.

Davies, J. M. 1993. Sandwich Panels. Journal of Thin-Walled Structures. 16(1-4): 179-198.

Othuman Mydin M. A., Rozlan, N. A., Ganesan S. 2015. Experimental Study on the Mechanical Properties of Coconut Fibre Reinforced Lightweight Foamed Concrete. Journal of Materials and Environmental Science. 6(2): 407-411.

Othuman Mydin, M. A., Y. C. Wang. 2012. Thermal and Mechanical Properties of Lightweight Foamed Concrete (LFC) at Elevated Temperatures. Magazine of Concrete Research. 64(3): 213-224.

Gleich, H. 2007. New Carbon Fiber Reinforcement Advances Sandwich Wall Panels. Structure Magazine. April: 61-63.

Othuman Mydin, M. A. 2011. Thin-walled Steel Enclosed Lightweight Foamed Concrete: A Novel Approach to Fabricate Sandwich Composite. Australian Journal of Basic and Applied Sciences. 5(12): 1727-1733.

Pessiki, S., and A. Mlynarczyk. 2003. Experimental Evaluation of Composite Behavior of Precast Concrete Sandwich Wall Panels. PCI Journal. 48 (2): 54-71.

Bush, T. D., and G. L. Stine. 1994. Flexural Behavior of Composite Prestressed Sandwich Panels. PCI Journal. 39(2): 112-121.

Lee, B., and S. Pessiki. 2007. Design and Analysis of Precast, Prestressed Concrete Three-Wythe Sandwich Wall Panels. PCI Journal. 52(4): 70-83.

Othuman Mydin, M. A., Y. C. Wang. 2012. Mechanical Properties of Foamed Concrete Exposed to High Temperatures. Journal of Construction and Building Materials. 26(1): 638-654.

Salmon, D. C., A. Einea, M. K. Tadros, and T. D. Culp. 1997. Full Scale Testing of Precast Concrete Sandwich Panels. ACI Structural Journal. 94(4): 354-362.

Frankl, B. 2008. Structural Behavior of Insulated Precast Prestressed Concrete Sandwich Panels Reinforced with CFRP Grid. M.Sc. thesis. Department of Civil, Construction and Environmental Engineering, North Carolina State University, Raleigh, NC.

Xu, Y. L. 1995. Determination of Wind-Induced Fatigue Loading on Roof Cladding. Journal of Engineering Mechanics, ASCE. 121(9): 956-963.

Othuman Mydin, M. A. 2013. Modeling of Transient Heat Transfer in Foamed Concrete Slab. Journal of Engineering Science and Technology. 8(3): 331-349

Shanmugam, N. E., Lakshmi. B. 2001. State of the Art Report on Steel-concrete Composite Columns. Journal of Constructional Steel Research. 57(1):1041-1080

Othuman Mydin, M. A. 2013. An Experimental Investigation on Thermal Conductivity of Lightweight Foamed concrete for Thermal Insulation. Jurnal Teknologi. 63(1): 43-49

Othuman Mydin, M. A., Y. C. Wang. 2011. Elevated-Temperature Thermal Properties of Lightweight Foamed Concrete. Journal of Construction & Building Materials. 25(2): 705-716.

Downloads

Published

2015-07-13

How to Cite

STRESS-STRAIN RELATIONSHIPS OF COMPOSITE FOAMED CONCRETE PANEL WITH DIFFERENT NUMBER OF SHEAR CONNECTORS UNDER COMPRESSION. (2015). Jurnal Teknologi (Sciences & Engineering), 75(5). https://doi.org/10.11113/jt.v75.4955