Effect of pH on Bovine Serum Albumin (BSA) Solution to Polysulfone-based Membrane

Authors

  • Nurul Nabilah Aminudin Faculty of Science, Technology and Human Development, Universiti Tun Hussein Onn Malaysia, Batu Pahat, 86400, Johor, Malaysia
  • Hatijah Basri Faculty of Science, Technology and Human Development, Universiti Tun Hussein Onn Malaysia, Batu Pahat, 86400, Johor, Malaysia
  • Muhammad Zaini Yunos Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, Batu Pahat, 86400, Johor, Malaysia
  • Zawati Harun Advanced Materials and Manufacturing Centre (AMMC), Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, Batu Pahat, 86400, Johor, Malaysia
  • Goh Pei Sean Faculty of Petroleum and Renewable Energy Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia

DOI:

https://doi.org/10.11113/jt.v70.3441

Keywords:

Polysulfone, polyethylene glycol, bovine serum albumin, phase inversion technique

Abstract

In this work, polysulfone (PSf) flat sheet membrane was prepared via phase inversion technique. The effects of polyethylene glycol (PEG) additive on membrane performance were observed and investigated. The membrane permeation was evaluated in terms of pure water flux (PWF) and solute rejection at different pHs (pH 3, pH 5, pH 7 and pH 9). Bovine serum albumin (BSA) solution was used to study the performance of the prepared membrane. Results showed that the increase of PEG concentration led to higher PWF. This is due to PEG role as a pore forming agent in casting solution. The PWF was found to increase up to 101.85 LMH at 5% PEG. However, the PWF decrease when the PEG concentration is increased up to 7% and 9%. Similarly, flux rate at different pH showed the same plot as PWF. At pH 9, the PWF is high compared to pH 3, pH 5 and pH 7. The BSA rejection data at pH 3 and pH 5 shows the high rejection compared to pH 7 and pH 9. No significant changes were observed when PEG concentration was increased. As a conclusion, the addition of PEG has improved the performance of membrane in terms of PWF at a certain percentage (with the highest was given at 5%) of PSf membrane. It is also evidenced that the % of BSA rejection increased with decreasing pH.

References

J. Y. Kim, H. K. Lee, S. C. Kim. 2000. Liquid-liquid Phase Separation During Polysulfone Membrane Preparation. Korean Jurnal Chemical Engineering. 17(5): 564–569.

Y. Haijun,C. Yiming, K. Guodong, L. Jianhui,M. Li ,Q. Yuana. 2009. Enhancing Antifouling Property of Polysulfone Ultrafiltration Membrane by Grafting Zwitterionic Copolymer via UV-initiated Polymerization. J. Membr. Sci. 342: 6–13.

L. Yan, Y. Li, C. Xiang, and S. Xianda. 2006. Effect of Nano-sized Al2O3-particle Addition on PVDF Ultrafiltration Membrane Performance. J. Membr. Sci. 276(1–2): 162–167.

K. W. L. Kenneth S. McGuire. 1995. Pore Size Distribution Determination from Liquid Permeation Through Microporous Membranes. J. Membr. Sci. 99: 127–137.

B. Chakrabarty, A. K. Ghosal, M. K. Purkait. 2008. Effect of Molecular Weight of PEG on Membrane Morphology and Transport Properties. J. Membr. Sci. 309: 209–221.

H. Basri, A. F. Ismail, & M. Aziz. 2011. Polyethersulfone (PES)-silver Composite Ultrafiltration Membrane: Effect of Silver Loading and PVP Molecular Weight on Membrane Morphology and Antibacterial Activity. Desalination. 273: 72–80.

N. A. A. Hamid, A. F. Ismail, T. Matsuura, A. W. Zularisam, W.J. Lau, E. Yuliwati & M. S. Abdullah. 2011. Morphological & Separation Performance Study of Polysulfone/Titanium Dioxide (PSf/TiO2) Ultrafiltration Membranes for Humic Acid Removal. Desalination. 273: 85–92.

B. Jung, J. K. Yoon, B. Kim and H. W. Rhee. 2004. Effects of Molecular Weight of Polymeric Additives on Formation, Permeation Properties and Hypochlorite Treatment of Asymmetric Polyacrylonitrile Membranes. J. Membr. Sci. 243: 45–47.

D. Kuzmenko, E.Arkhangelsky, S. Belfer, V. Freger, V. Gitis. 2005. Chemical Cleaning of UF Membranes Fouled by BSA. Desalination. 179 323–333.

G. Arthanareeswaran, D. Mohan and M. Raajenthiren. 2007. Preparation and Performance of Polysulfone-sulfonated Poly(Ether Ether Ketone) Blend Ultrafiltration Membranes. Part I. Applied Surface Science. 253: 8705–8712.

C. Feng, R. Wang, B. Shi, G. Li and Y. Wu. 2006. Factors Affecting Pore Sturcture and Performance of Poly(vinylidene fluoride-co-hexafluoro propylene) Asymmetric Porous Membrane. J. Membr. Sci. 277(1–2): 55–64.

W. L. Chou, D. G. Yu, M. C. Yang and C. H. Jou. 2007. Effect of Molecular Weight and Concentration of PEG Additives on Morphology and Permeation Performance of Cellulose Acetate Hollow Fibers. Sep. Purif. Technol. 57: 207–217.

R. Muppalla, H. H. Rana, S. Devi and S. K. Jewrajka. 2013. Adsorption of pH-responsive Amphiphilic Copolymer Micelles and Gel on Membrane Surface as an Approach for Antifouling Coating. App. Surf. Sci. 268: 355–367.

S. Fakhfakh, S. Baklouti, Samir Baklouti, J. Bouaziz. 2010. Preparation, Characterization and Application in BSA Solution of Silica Ceramic Membranes. Desalination. 262: 188–19.

Downloads

Published

2014-09-02

How to Cite

Effect of pH on Bovine Serum Albumin (BSA) Solution to Polysulfone-based Membrane. (2014). Jurnal Teknologi (Sciences & Engineering), 70(2). https://doi.org/10.11113/jt.v70.3441