Discrete Element Modelling of Complex Failure Mechanism at Quarry Slope
DOI:
https://doi.org/10.11113/jt.v72.4010Keywords:
Discrete element method, UDEC, rock slope, block-flexural topplingAbstract
Road cutting, open pit mining, quarrying and various other constructions in hilly terrain demand special attention in terms of slope stability. The analysis of slope stability is of great significance not only for ensuring safe design of excavated slope, but also for preventing potential hazards. This research was undertaken to identify the controlling parameters affecting the slope instability. As the rock slope behaviour is mostly governed by discontinuities, discontinuum numerical technique such as Discrete Element Method (DEM) which has the ability to address discontinuity controlled instability is well suited for this case. This study investigated the failure pattern and its responsible factors leading to failure of a slope at a slate quarry situated in Wales, United Kingdom as a case study. The research work consisted of field investigation, laboratory experiments and parametric analysis by powerful and renowned distinct element computational tool Universal Discrete Element Code (UDEC). Evidence showed that complex failure mechanism involving distinct planar sliding surface along with block-flexural toppling contributed to the instability at the studied slate quarry. Dip of discontinuity, presence of water, weathering state and slope angle were the significant factors found in this study to have profound impact on controlling rock slope instability. The modelling results also indicated that the influence of structurally dipping at 78° of cleavage in slate and the water filling in the crack which developed excess water pressure have triggered the failure.Â
References
Deere, D.U., A.J. Hendron, F.D. Patton and E.J. Cording. 1967. Design of surface and near surface construction in rock. Proc. 8th U.S. Symp. Rock Mech. New York: AIME. 237–302.
Wickham, G.E., H.R. Tiedemann, and E.H. Skinner. 1972. Support determination based on geological prediction. Proc. North American Rapid Excav. Tunnelling Conf. New York: AIME. 43–64.
Bieniawski, Z.T. 1989. Engineering Rock Mass Classifications: A Complete Manual For Engineers And Geologists In Mining, Civil And Petroleum Engineering. New York: John Wiley and Sons.
Barton, N., R. Lien, and J. Lunde.1974. Engineering classification of rock masses for the design of tunnel support. Rock Mechanics. 6(4): 189–236.
Hoek, E. and E.T. Brown. 1997. Practical Estimates of rock mass strength. Int. J. Rock Mech. Min. Sci. 34(8): 1165–186.
Palmstrøm, A. 1996. Characterizing rock masses by RMi for use in practical rock engineering. Tunnelling and Underground Space Technology. 11(2): 175–188.
E. Romana, M., J.B. Serón, and E. Montalar. 2003. SMR Geomechanics classifcation: Application, experience and validation. Proceedings of the 10th Congress of the International Society for Rock Mechanics: ISRM 2003 - Technology Roadmap for Rock Mechanics, South African Institute of Mining and Metallurgy. 1–4.
Laubscher, D.H. 1977. Geomechanics classification of jointed rock masses - mining application. Trans. Instn. Min. Metall. (Sect. A: Min. Industry). 86: A1–A8.
Sonmez, H. and R. Ulusay. 1999. Modifications to the geological strength index (GSI) and their applicability to stability of slopes. Int. J. Rock Mech. Min. Sci. 36: 743-760.
Hudson, J.A. and J.P. Harrison. 1992. A new approach to studying complete rock engineering problems. Quarterly Journal of Engineering Geology. 25: 93–105.
Hack, R., D. Price, and N. Rengers. 2003. A new approached to rock slope stability - a probability classification (SSPC). Bulletin of Engineering Geology and the Environment. 62(2): 167–184.
Nicholson, D.T. 2004. Hazard assessment for progressive, weathering related breakdown of excavated rockslopes. Quarterly Journal of Engineering Geology and Hydrogeology. 37: 327–346.
Pantelidis, L. 2010. An alternative rock mass classification system for rock slopes. Bulletin of Engineering Geology and the Environment. 69(1): 29–39.
Li, X. 2007. Finite element analysis of slope stability using a nonlinear failure criterion. Computer and Geotechnics. 34(3): 127–136.
Alejano, L.R., A.M. Ferrero, P. RamÃrez-Oyanguren, M. I. Ãlvarez Fernández. 2011. Comparison of limit equilibrium, numerical and physical models of wall slope stability. Int. J. Rock Mech. Min. Sci. 48(1): 16–26.
Cheng, Y.M., T. Lansivaara, and W.B. Wei. 2007. Two-dimensional slope stability analysis by limit equilibrium and strength reduction methods. Computers and Geotechnics. 34(3): 137–150.
Bhasin, R. and K. Hoeg. 1998. Parametric study for a large cavern in jointed rock using a distinct element model (UDEC - BB). Int. J. Rock Mech. Min. Sci. 35(1): 17–29.
Brideau, M.A., D. Stead, and R. Couture. 2006. Structural and engineering geology of East Gate Landslide, Purcell Mountains, British Columbia, Canada. Engineering Geology. 84(3/4)): 183–206.
McCollough, M.F. 1993. Numerical modelling with UDEC of the footwall slope of Aznalcollar mine, Southern Spain. M.Sc. Thesis, Department of Mining & Mineral Engineering, University of Leeds, United Kingdom. 143.
Preh, A. and R. Poisel 2004. A UDEC model for "kink-band slumping" type failures of rock slopes. Proc. of the 1st Int. UDEC/3DEC Symp., Bochum, Germany, Balkema: Numerical Modelling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences. London: Taylor & Francis Group. 243–247
Choi, S.O. and S.K. Chung. 2004. Stability analysis of jointed rock slope with the Barton-Bandis constitutive model in UDEC. Int. J. Rock Mech. Min. Sci. 41(3): 1–6.
Allison, R.J. and O.G. Kimber. 1998. Modelling failure mechanism to explained rock slope change along the Isle of Purbeck Coast, UK. Earth Surface Processes and Landforms. 23(8): 731–750.
Mitani, Y., T. Esaki, and Y. Cai. 2004. A numerical study about flexure toppling phenomenon on rock slopes. Proc. of the 1st Int. UDEC/3DEC Symp., Bochum, Germany, Balkema: Numerical Modelling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences. London: Taylor & Francis Group. 235–241.
Bhasin, R. and A.M. Kaynia. 2004. Static and dynamic simulation of a 700-m high rock slope in western Norway. Engineering Geology. 71: 213–226.
Tosney, J.R., D. Milne, A.V. Chance and F. Amon. 2004. Verification of a large scale slope instability mechanism at Highland Valley Copper. International Journal of Mining, Reclamation and Environment. 18(4): 273–288.
Hack, R. 2002. An evaluation of slope stabiliy classification. Proceedings of ISRM International Symposium, EUROCK 2002: Rock Engineering for Mountainous Regions. 3–32.
Bell, F.G. 1981. Engineering Properties of Soils and Rocks. London: Butterworths. 149.
Digimap. 2011. Retrieved October 10, 2011, from http://digimap.edina.ac.uk/digimap/home
Abdullah, R.A., R.J. Fowell, and W. Murphy. 2010. Selecting shear strength models for joints - experience with modelling of complex rock slope failure in UDEC. Proceedings of the European Rock Mechanics Symposium, EUROCK 2010: Rock Mechanics in Civil and Environmental Engineering. Switzerland: Taylor & Francis Group. 543–546.
Itasca. 2004. UDEC Version 4.01. Minneapolis, Minnesota, USA: Itasca Consulting Group, Inc.
Bhasin, R. 2008. Barton Bandis joint model in UDEC. Personal communication.
Brox, D. and W. Newcomen. 2003. Utilizing strain criteria to predict highwall stability performance. Proceedings of the 10th Congress of the International Society for Rock Mechanics: ISRM 2003–Technology Roadmap for Rock Mechanics, South African Institute of Mining and Metallurgy. 157–161.
Bandis, S.C., A.C. Lumsden, and N.R. Barton. 1983. Fundamentals of rock joint deformation. Int. J. Rock Mech. Min. Sci. 20(6): 249–268.
Abdullah, R.A. 2011. Development of a slope classification system with particular reference to shallow rock slope failure. Ph.D. Thesis, School of Process, Environmental and Materials Engineering, University of Leeds, United Kingdom. 210.
Downloads
Published
Issue
Section
License
Copyright of articles that appear in Jurnal Teknologi belongs exclusively to Penerbit Universiti Teknologi Malaysia (Penerbit UTM Press). This copyright covers the rights to reproduce the article, including reprints, electronic reproductions, or any other reproductions of similar nature.
