Hardware Development of Reflection Mode Ultrasonic Tomography System for Monitoring Flaws on Pipeline

Authors

  • Norsuhadat Nordin Faculty of Petroleum and Renewable Energy Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • Mariani Idroas Faculty of Petroleum and Renewable Energy Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • Zainal Arifin Zakaria Faculty of Petroleum and Renewable Energy Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • M. Nasir Ibrahim Faculty of Electrical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia

DOI:

https://doi.org/10.11113/jt.v73.4240

Keywords:

Pipeline, ultrasonic, flaws, tomography, modelling

Abstract

The pipeline inspection is a key requirement to maintain structural health and pipeline integrity for oil and gas transportation over countries. Pipe failure is a critical problem that needs to be endured within the operational work. The defects or flaws existence on pipeline surface is one of the most leading factors to pipe failures. A new approach of non-destructive technique is implemented to monitor flaws on pipeline by using reflection-mode ultrasonic tomography system. This paper details on the hardware development of ultrasonic tomography system based on reflection mode detection. The system consists of ultrasonic transceiver sensors mounted circularly and contactless to the pipe surface. The modeling work described the ultrasonic ring configuration, ultrasonic signal behavior, sensors arrangement and image grid estimation. The developed instrumentation system is used to detect external and internal flaws on pipe surface. The results show that the reflection-mode ultrasonic tomography is capable to differentiate flaws detected based on the calculated depth verified from the distance measured and through the reconstructed image.

References

NDT Global. 2014. Crack Detection and Pipeline Integrity Solutions. [Brochure]. Rusia: NDT Global.

M. Beller, E. Holden, and N. Uzelac. 2001. Cracks in Pipelines and How to Find Them. Pipes & Pipelines International.

J. Li, and J. L. Rose. 2002. Angular-Profile Tuning of Guided Waves in Hollow Cylinders Using a Circumferential Phased Array. IEEE. 49(12).

J. Blitz, and G. Simpson. 1996. Ultrasonic Methods of Non-Destructive Testing. 1st ed. London, UK: Champman& Hall.

M. Beller, and H. Schoenmaker. 1996. Pipeline Inspection: A Turnkey Approach. Pipeline Pigging and Integrity Monitoring Conference. Jakarta

R. Abdul Rahim, M. H. Fazalul Rahiman, and K. S. Chan. 2004. On Monitoring Liguid/Gas Flow Using Ultrasonic Tomography. Journal Teknologi. 40(D): 77–88.

S. Ibrahim, M. A. Md Yunus, M. T. Md Khairi, and M. Faramarzi. 2014. A Review on Ultrasonic Process Tomography System. Jurnal Teknologi 70: 3.

S. Z. Mohd. Muji, R. Abdul Rahim, M. H. Fazalul Rahiman, S. Sahlan, M. F. Abdul Shaib, M. J. Pusspanathan, and, E. J. Mohammad. 2011. Optical Tomography: A Review on Sensor Array, Projection Arrangement and Image Reconstruction Algorithm. International Journal of Innovative Computing, Information and Control. 7(7(A)): 3839–3856.

M. D. Supardan,Y. Masudab, A. Maezawab, and S. Uchidab. 2007. The Investigation of Gas Holdup Distribution in A Two-Phase Bubble Column using Ultrasonic Computed Tomography. Chemical Engineering Journal. 130: 125–133.

R. Abdul Rahim, N. W. Nyap, and M. H. Fazalul Rahiman. 2007. Hardware Development of Ultrasonic Tomography for Composition Determination of Water and Oil Flow. Sensor & Transducer Journal. 75: 904–913.

M. H. Fazalul Rahiman, R. Abdul Rahim, H. Abdul Rahim, and N. M. Nor Ayob. 2012. Design and Development of Ultrasonic Process Tomography. In Santos (Ed.). Ultrasonic Waves. 211–226.

J. H. Charles. 2003. Ultrasonic Testing. In: Robert, C.M. and Samuel A. W. Handbook of Non-Destructive Evaluation. US: McGraw-Hill. 301–416.

M. Yang, H. I. Schlaberg, B. S. Hoyle, M. S. Beck, and C. Lenn. 1999. Real-time Ultrasound Process Tomography for Two-phase Flow Imaging using a Reduced Number of Transducers. IEEE Transactions on Ultrasonic, Ferroelectrics and Frequency Control. 46.

Z. Zulkarnay. 2010. Simulation of the Two-Phase Liquid-Gas Flow through Ultraosnic Transceivers Application in Ultrasonic Tomography. Sensors & Transducers.

P. M. Donald. 1999. Choosing an Ultrasonic Sensor for Proximity or Distance Measurement Part 2: Optimizing Sensor Selection. Unpublished.

Downloads

Published

2015-03-18

How to Cite

Hardware Development of Reflection Mode Ultrasonic Tomography System for Monitoring Flaws on Pipeline. (2015). Jurnal Teknologi (Sciences & Engineering), 73(3). https://doi.org/10.11113/jt.v73.4240