INVESTIGATION OF THERMAL DEGRADATION OF POULTRY PROCESSING DEWATERED SLUDGE USING THERMOGRAVIMETRIC ANALYSIS METHOD

Authors

  • N. Aniza Mechanical Engineering Department, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Malaysia
  • S. Hassan Mechanical Engineering Department, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Malaysia
  • M. F. M. Nor Mechanical Engineering Department, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Malaysia
  • K. E. Kee Mechanical Engineering Department, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Malaysia
  • Aklilu T. Mechanical Engineering Department, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Malaysia

DOI:

https://doi.org/10.11113/jt.v76.5522

Keywords:

Heating rate, particle size, poultry sludge, TGA, thermal degradation

Abstract

Thermal degradation of Poultry Processing Dewatered Sludge (PPDS) was studied using thermogravimetric analysis (TGA) method. The effect of particle size on PPDS samples and operational condition such as heating rates were investigated. The non-isothermal TGA was run under a constant flow of oxygen at a rate of 30 mL/min with temperature ranging from 30ºC to 800ºC. Four sample particle sizes ranging between 0.425 mm to 2 mm, and heating rate between 5 K/min to 20 K/min were used in this study. The TGA results showed that particle size does not have any significant effect on the thermogravimetry (TG) curves at the initial stage, but the TG curves started to separate explicitly at the second stage. Particle size may affect the reactivity of sample and combustion performance due to the heat transfer and temperature gradient. The TG and peak of derivative thermogravimetry (DTG) curves tend to alter at high temperature when heating rate is increased most likely due to the limitation of mass transfer and the delay of degradation process. 

References

Damartzis, T. and Zabaniotou, A. 2011. Thermochemical conversion of biomass to second generation biofuels through integrated process design—A review. Renew. Sustain. Energy Rev. 15(1): 366–378.

Dirion, J.-L., Reverte, C. and Cabassud, M. 2008. Kinetic parameter estimation from TGA: Optimal design of TGA experiments. Chem. Eng. Res. Des. 86(6): 618–625.

Otero, M., Gómez, X., García, A.L. and Morán, A. 2007. Effects of sewage sludge blending on the coal combustion: a thermogravimetric assessment. Chemosphere. 69(11): 1740–1750.

Shawalliah, S., Abd, N. and Ismail, K. 2012. Combustion characteristics of Malaysian oil palm biomass , sub-bituminous coal and their respective blends via thermogravimetric analysis ( TGA ). Bioresour. Technol. 123: 581–591.

Chouchene, A., Jeguirim, M., Khiari, B., Zagrouba, F. and Trouvé, G. 2010. Thermal degradation of olive solid waste: Influence of particle size and oxygen concentration. Resour. Conserv. Recycl. 54(5):271–277.

Harun, N. Y., Afzal, M. T. and Shamsudin, N. Reactivity Studies of Sludge and Biomass Combustion. Int. J. Eng. 3(5): 413–425.

Marcilla, A., García, A. N., Pastor, M. V.,León, M., Sánchez, A. J. and Gómez, D. M. 2013. Thermal decomposition of the different particles size fractions of almond shells and olive stones. Thermal behaviour changes due to the milling processes. Thermochim. Acta. 564: 24–33.

Idris, S. S., Rahman, N. A. and Ismail, K. 2012. Combustion characteristics of Malaysian oil palm biomass, sub-bituminous coal and their respective blends via thermogravimetric analysis (TGA). Bioresour. Technol.123: 581–59.

Mohammed, M. A. A., Salmiaton, A., Azlina, W. A. K. G. W. and Amra, M. S. M. 2012. Gasification of oil palm empty fruit bunches: A characterization and kinetic study. Bioresour. Technol.110: 628–636.

Vamvuka, D. and Sfakiotakis, S. 2011. Combustion behaviour of biomass fuels and their blends with lignite. Thermochim. Acta. 526(1–2): 192–199.

Downloads

Published

2015-09-14

Issue

Section

Science and Engineering

How to Cite

INVESTIGATION OF THERMAL DEGRADATION OF POULTRY PROCESSING DEWATERED SLUDGE USING THERMOGRAVIMETRIC ANALYSIS METHOD. (2015). Jurnal Teknologi (Sciences & Engineering), 76(5). https://doi.org/10.11113/jt.v76.5522