THE EFFECTS OF THE DIE HALF ANGLE OF TAPER DIE ON PLANE STRAIN EXTRUSION
DOI:
https://doi.org/10.11113/jt.v78.9654Keywords:
Die half angle, extrusion, paraffinic mineral oil, RBD palm stearin, visioplasticity, extrusion load, surface roughnessAbstract
In this research, a study of the effect of a die half angle on the extrusion process has been performed. The experiments were conducted at room temperature around 27 °C. Two types of taper die with different die half angles (45° and 60°) were prepared. The test lubricants used were paraffinic mineral oil VG460 and Refined, Bleached and Deodorized (RBD) Palm stearin. The material of the workpiece (billet) was annealed with A1100 aluminium. The experimental results were focused on the extrusion load, tool and workpiece surface roughness and plastic deformation of the workpiece. The resultant relative velocity was calculated using a visioplasticity method. The results shows that a taper angle of 60° recorded higher resultant relative velocity with a lower extrusion load and surface roughness compare to the taper angle of 45°. The comparison study between Paraffinic Mineral Oil and RBD Palm Stearin shows no significant effect in both taper angles tested.
References
Abdulquadir, B. L., Adeyemi, M. B 2008. Evaluations Of Vegetable Oil Based As Lubricants For Metal-Forming Processes. Ind Lubr Tribol. 60: 242-248.
Caminaga, C., Frederico, O. N., Fernnando, C. G., Sergio, T. B. 2007. Study of Alternative Lubricants to the Cold Extrusion of Steel Shafts. J Mater Process Tech. 182: 432-439.
Chaudhari, G. A., Andhale, S. R., Patil, N. G. 2012. Experimental Evaluation of Effect of Die Angle on Hardness and Surface Finish of Cold Forward Extrusion of Aluminum. International Journal of Emerging Technology and Advanced Engineering. 2: 334-338.
Gariety, M., Ngaile, G., Altan, T. 2007. Evaluation of New Cold Forging Lubricants without Zinc Phosphate Precoat. Int J Mach Tool Manu. 47: 673-681.
Hosseini, S.H., Abrinia, K., Faraji, G. 2015. Applicability of a Modified Backward extrusion Process on Commercially Pure Aluminum. Mater Design. 65: 521-528.
Syahrullail, S., Azwadi, C. S. N., Najib, Y. M. 2013a. The Influences Of The Die Half Angle Of Taper Die During Cold Extrusion Process. Arab J Sci Eng. 38: 1201-1207.
Syahrullail, S., Nakanishi, K., Kamitani, S. 2013b. Investigation of the Effects of Frictional Constraint with Application of Palm Olein Oil Lubricant and Paraffin Mineral Oil Lubricant on Plastic Deformation by Plane Strain Extrusion. J Jpn Soc Tribol. 50: 877-885.
Syahrullail, S., Zubil, B. M., Azwadi, C. S. N, Ridzuan, M. J. M. 2011. Experimental Evaluation of Palm Oil as Lubricant in Cold Forward Extrusion Process. Int J Mech Sci. 53: 549-555.
Tiernan, P., Hillery, M. T., Draganescu, B., Gheorghe, M. 2005. Modelling Of Cold Extrusion with Experimental Verification. J Mater Process Tech. 168: 360-366.
Wang, L., Zhou, J., Duszczyk, J., Katgerman, L. 2012. Friction in Aluminium Extrusion- Part 1: A Review of Friction Testing Techniques for Aluminium Extrusion. Tribol Int. 56: 89-98.
Masjuki, H. H., M. A. Maleque, A. Kubo and T. Nonaka. 1999. Palm Oil And Mineral Oil Based Lubricants—Their Tribological And Emission Performance. Tribology International. 32(6): 305-314.
Masjuki, H. H. and M. A. Maleque. 1996. The Effect Of Palm Oil Diesel Fuel Contaminated Lubricant On Sliding Wear Of Cast Irons Against Mild Steel. Wear. 198(1-2): 293-299.
Golshokouh, S. Syahrullail, F. Nasir Ani, and H. H. Masjuki. 2013a. Investigation Of Palm Fatty Acid Distillate As An Alternative Lubricant Of Petrochemical Based Lubricants, Tested At Various Speeds. Int. Rev. Mech. Eng. 7(1): 72-80.
Golshokouh. I, M. Golshokouh, F. N. Ani, E. Kianpour, and S. Syahrullail. 2013b. Investigation Of Physical Properties For Jatropha Oil In Different Temperature As Lubricant Oil. Life Science Journal. 10(8): 110-119.
Nuraliza, N., S. Syahrullail and M. H. Faizal. 2016. Tribological Properties Of Aluminum Lubricated With Palm Olein At Different Load Using Pin-On-Disk Machine. Jurnal Tribologi. 9: 45-59.
Binfa Bongfa, Peter, A. Atabor Atuci Banabas and M. O. Adeoti. 2015. Comparison Of Lubricant Properties Of Castor Oil And Commercial Engine Oil. Jurnal Tribologi. 5: 1-10.
Downloads
Published
Issue
Section
License
Copyright of articles that appear in Jurnal Teknologi belongs exclusively to Penerbit Universiti Teknologi Malaysia (Penerbit UTM Press). This copyright covers the rights to reproduce the article, including reprints, electronic reproductions, or any other reproductions of similar nature.
