INVESTIGATION OF MICRO-PITS FORMATION ON BILLET SURFACES IN PLANE STRAIN EXTRUSION

Authors

  • I. M. Izhan Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • S. Syahrullail Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • S. Y. Yong Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • M. A. Nurul Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia

DOI:

https://doi.org/10.11113/jt.v78.9666

Keywords:

Vegetable oil, cold extrusion, paraffinic mineral oil, RBD Palm stearin, surface roughness

Abstract

Extrusion is a process of pushing a material through a die to yield a desired cross-section product. The application of surface texture has become well known for enhancing tribological performance. In this research, the effect of micro-pits embedded on a work piece lubricated with vegetable oil using plain strain extrusion were studied and compared with those seen with mineral-based oil lubricant. The experiments were conducted at room temperature (around 27℃). A taper die with a 60 die half-angle, with micro-pits array, was prepared. Test lubricants used were paraffinic mineral oil (PMO) VG460 and VG95 and refined, bleached and deodorized (RBD) palm stearin. The results were analysed to determine the extrusion load and the billet’s surface roughness and plastic deformation. RBD palm stearin was recorded as having the highest extrusion load (83.15 kN).

References

Manabu Wakuda, Yukihiko Yamauchi, Shuzo Kanzaki, Yoshiteru Yasuda. 2003. Effect Of Surface Texturing On Friction Reduction Between Ceramic And Steel Materials Under Lubricated Sliding Contact. Wear. 254: 356-363.

Hafis, S. M., Ridzuan, M. J. M., Farahana, R. N., Ayob, A., Syahrullail, S. 2013. Paraffinic Mineral Oil Lubrication For Cold Forward Extrusion: Effect Of Lubricant Quantity And Friction. Tribology International. 60: 111-115.

Chiong Ing, T., Rafiq, A. K. M., Azli, Y., Syahrullail, S. 2012. Tribological Behaviour Of Refined Bleached And Deodorized Palm Olein In Different Loads Using A Four-Ball Tribotester. Scientia Iranica. 19(6): 1487-1492.

Syahrullail, S., Azwadi, C. S. N., Ing, T. C. 2011. The Metal Flow Evaluation Of Billet Extruded With RBD Palm Stearin. International Review of Mechanical Engineering. 5(1): 21-27.

A. Borghi, E. Gualtieri, D. Marchetto, L. Moretti, S. Valeri. 2008. Tribological Effects Of Surface Texturing On Nitriding Steel For High Performance Engine Applications. Wear. 265: 1046-1051.

Andriy Kovalchenko, Oyelayo Ajayi, Ali Erdemir, George Fenske, Izhak Etsion. 2005. The Effect Of Laser Surface Texturing On Transitions In Lubrication Regimes During Unidirectional Sliding Contact. Tribology International. 38: 219-225.

Dangsheng Xiong, Yongkun Qin, Jianliang Li, Yi Wan, Rajneesh Tyagi. Tribological Properties Of PTFE/Laser Surface Textured Stainless Steel Under Starved Oil Lubrication. Tribology International.

Stachowiak, G. W., Batchelor, A. W. 2005. Engineering Tribology. Elsevier Butterworth Heinemann.

Bowden, F. P., Tabor, D. 2001. The Friction And Lubrication Of Solids. Oxford Classic Series, Oxford University Press.

Syahrullail, S., Nakanishi, K., Kamitani, S. 2005. Investigation Of The Effects Of Frictional Constraint With Application Of Palm Olein Oil Lubricant And Paraffin Mineral Oil Lubricant On Plastic Deformation By Plane Strain Extrusion. Journal of Japanese Society of Tribologists. 50(12): 55-63.

Wei Tang, Yuankai Zhou, Hua Zhu, Haifeng Yang. 2013. The Effect Of Surface Texturing On Reducing The Friction And Wear Of Steel Under Lubricated Sliding Contact. Applied Surface Science. 273: 199-204.

Taposh Roy, Dipankar Choudhury, Azuddin Bin Mamat, Belinda Pingguan-Murphy. Fabrication and Characterization Of Micro-Dimple Array On Al2O3 Surfaces By Using A Micro-Tooling.

Maleque, M. A., Masjuki, H. H., Haseeb, A. S. M. A. 2000. Effect Of Mechanical Factors On Tribological Properties Of Palm Oil Methyl Ester Blended Lubricant. Wear. 239: 117-25.

Mahdavian, S. M. 1982. A Refined Analytical Model For Hydrodynamic Lubrication Of Cold Extrusion And Its Comparison With Experiment. Journal Of Lubrication Technology. 104: 46-52.

Downloads

Published

2016-10-04

How to Cite

INVESTIGATION OF MICRO-PITS FORMATION ON BILLET SURFACES IN PLANE STRAIN EXTRUSION. (2016). Jurnal Teknologi (Sciences & Engineering), 78(10-2). https://doi.org/10.11113/jt.v78.9666