DEVELOPMENT AND EVALUATION OF AN AUTOMOTIVE AIR-CONDITIONING TEST RIG

Authors

  • Ahmad Zulkhairie Amran Automotive Development Centre (ADC), Faculty of Mechanical Engineering, Institute for Vehicle Systems and Engineering (IVeSE) Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • Zulkarnain Abdul Latiff Automotive Development Centre (ADC), Faculty of Mechanical Engineering, Institute for Vehicle Systems and Engineering (IVeSE) Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • Henry Nasution Automotive Development Centre (ADC), Faculty of Mechanical Engineering, Institute for Vehicle Systems and Engineering (IVeSE) Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • Mohd Rozi Mohd Perang Automotive Development Centre (ADC), Faculty of Mechanical Engineering, Institute for Vehicle Systems and Engineering (IVeSE) Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • Hishammudin Mohd Jamil Automotive Development Centre (ADC), Faculty of Mechanical Engineering, Institute for Vehicle Systems and Engineering (IVeSE) Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • Mohd Nazri Misseri Automotive Development Centre (ADC), Faculty of Mechanical Engineering, Institute for Vehicle Systems and Engineering (IVeSE) Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia

DOI:

https://doi.org/10.11113/jt.v78.9668

Keywords:

Automotive refrigeration, test rig, variable evaporator blower speed

Abstract

To evaluate an air-conditioning system performance on board is quite cumbersome and tedious process due to the limitation of space in the engine compartment. This paper presents the process of designing and the result from the automotive refrigeration system simulation that have been integrated into the test rig. To perform the test on automotive refrigeration simulator the location for the temperature measurement selected and thermocouples were installed. The locations of the temperature probes are at the inlet and outlet of compressor, condenser outlet and the inlet of the evaporator. The gas pressure was measured at low and high pressure sides located at evaporator outlet and receiver-drier respectively. The test results were analyzed using the properties table of the refrigerant used. The coefficient of performance (COP), cooling load of the system and compressor power consumption were determined. The variable parameters used are the evaporator blower speed and the air velocity passes through the condenser. The experimental results obtained show that increasing the blower speed will reduce the COP of the refrigeration system. The maximum COP of the system is 4.3 at the lowest evaporator blower speed. The power consumption will be reduced when the air flow velocity through the condenser is increased from 0, 40, 50, 60, 70 km/h respectively.

References

ANSI/ASHRAE Standard 55. 2008. Thermal Environmental Conditions For Human Occupancy. American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.

Y. A. Cengel and M. A. Boles. 2011. Thermodynamics: An Engineering Approach. 7th Ed. in SI Units. New York, America: McGraw-Hill.

Joudi, K. A., Mohammed, A. S. K., Aljanabi, M. K. 2003. Experimental and Computer Performance Study of an Automotive Air conditioning System with Alternative Refrigerants. Energy Conversion and Management. 44: 2959-2976.

Bhatti, M. S. 1999. Riding in Comfort, Part II: Evolution of Automotive Air Conditioning. ASHRAE Journal. 41(9): 44-52.

Kargilis, A. 2003. Design and Development of Automotive Air Conditioning Systems. ALKAR Engineering. 1-3.

Santanu, P. Datta, Prasanta K. Das and Siddhartha Mukhopadhyay. 2013. Performance of an Off-Board Test Rig for an Automotive Air Conditioning System. International Journal of Air-Conditioning and Refrigeration. 21(03): 1-17.

Kiatsiriroat, T., Euakit, T. 1997. Performance Analyses of an Automotive Air Conditioning System with R22/R124/R152A Refrigerant. Applied Thermal Engineering. 17(11): 1085-1097.

Schwarz, T., Galluzzi, M., Richardson, D., Radermacher, R., Dickson, T., McGregor, I. 2002. Model To Investigate The Performance Of Accumulators In Vapor Compression Systems. Proc.9th Int. Refrigeration and Air Conditioning Conference at Purdue.

F. W. Yu and K. T. Chan. 2006. Advanced Control of Heat Rejection Airflow for Improving the Coefficient of Performance of Air Cooled Chillers. Applied Thermal Engineering. 26: 97-110.

Haslinda Mohamed Kamar, Mohd Yusoff Senawi and Nazri Kamsah. 2013. Computerized Simulation of Automotive Air Conditioning System: A Parametric Study. International Journal of Computer Science Issues. 10(1): 787-794.

Mark Schubel. 2009. Today’s Technician: Automotive Heating and Air Conditioning for Classroom Manual. 4th Ed. NY, USA. Delmar Cengage Learning.

Saiz Jabardo, J. M., Gonzalez Mamani, W., Ianella, M. R. 2002. Modeling and Experimental Evaluation of an Automotive Air Conditioning System with a Variable Capacity Compressor. Int, J, Refrig. 25(8): 1157-1172.

Afiq Aiman Dahlan. 2012. Performance Characteristics Study of Cooling Capacity in Engine Speed Rotation using HFC-r134a and HC-r134a. Thesis of Undergraduate Project, Universiti Teknologi Malaysia.

Lee, G. H., Yoo, J. Y. 2014. Performance and Simulation of Automobile Air Conditioning System. International Journal Refrigeration. 23: 243-254.

Ianella, M. R. 1998. Theoretical And Experimental Analysis Of An Automotive Air Conditioning System. MSc thesis. University of Sao Paulo, Sao Carlos, Brazil.

Downloads

Published

2016-10-04

How to Cite

DEVELOPMENT AND EVALUATION OF AN AUTOMOTIVE AIR-CONDITIONING TEST RIG. (2016). Jurnal Teknologi (Sciences & Engineering), 78(10-2). https://doi.org/10.11113/jt.v78.9668