MICROSTRUCTURAL INVESTIGATION AND MECHANICAL PROPERTIES OF THIXOFORMED AL-6SI-XCU-0.3MG ALLOYS
DOI:
https://doi.org/10.11113/jt.v79.11279Keywords:
Aluminium alloys, cooling slope casting, thixoforming, mechanical properties, fracture behaviourAbstract
In this study, the effect of different amounts of copper (CU) on the microstructure and mechanical properties of thixoformed Al-6Si-xCu-0.3Mg (x= 3, 4 and 5, mass fraction, %) were investigated. The alloys were prepared via cooling slope casting technique, before there were thixoformed using compression press. All of the alloys were then characterized using optical microscope (OM), scanning electron microscope (SEM) and energy dispersive X-ray (EDX). The results obtained revealed that cooling slope casting produced a non-dendritic microstructure and the intermetallic phase in the thixoformed samples was refined and evenly distributed. The results also revealed that as the Cu content in the alloy increases, the hardness and tensile strength of the thixoformed alloys also increase. The hardness of thixoformed Al-6Si-3Cu was 104.1 HV while the hardness of Al-6Si-5Cu alloy was increased to 118.2 HV. The ultimate tensile strength, yield strength and elongation to fracture of the thixoformed alloy which contained 3wt.% Cu were 241 MPa, 176 MPa and 3.2% respectively. The ultimate tensile strength, yield strength and elongation to fracture of the alloy that contained 6wt.% of Cu were 280 MPa, 238 MPa and 1.2% respectively. The fracture surface of the tensile sample with lower Cu content exhibited dimple rupture while higher Cu content showed a cleavage fracture.
References
Abedi, A., Shahmiri, M., Amir Esgandari, B. and Nami, B. 2013. Microstructural Evolution During Partial Remelting of Al−Si Alloys Containing Different Amounts of Magnesium. Journal of Materials Science & Technology. 29(10): 971-978.
Mohammed, M. N., Omar, M. Z., Salleh, M. S., Alhawari, K. S. and Kapranos, P. 2013. Semi-Solid Metal Processing Techniques for Non-Dendritic Feedstock Production. The Scientific World Journal. 2013: 1-9.
Salleh, M. S., Omar, M. Z. and Syarif, J. 2015. The Effects of Mg Addition on the Microstructure and Mechanical Properties of Thixoformed Al–5%Si–Cu Alloys. Journal of Alloys and Compounds. 621: 121-130.
Salleh M. S, Omar, M. Z., Syarif, J. and Mohammed, M. N. 2013. An Overview of Semisolid Processing of Aluminium Alloys. ISRN Materials Science. 2013: 1-9.
Birol, Y. 2007. A357 Thixoforming Feedstock Produced by Cooling Slope Casting. Journal of Materials Processing Technology. 186(1-3): 94-101.
Atkinson, H. V. 2012. Alloys for Semi-Solid Processing. Solid State Phenomena. 192-193: 16-27.
Haga, T. and Suzuki, S. 2001. Casting of Aluminium Alloys Ingots for Thixoforming Using A Cooling Slope. Journal of Materials Processing Technology. 118: 169-172.
Salleh, M. S., Omar, M. Z. Syarif, J., Alhawari, K. S. and Mohammed, M. N. 2014. Microstructure and Mechanical Properties of Thixoformed A319 Aluminium Alloy. Materials and Design. 64: 142-152.
Liu, D., Atkitson, H. V. and Jones. H. 2005. Thermodynamic Prediction of Thixoformability In Alloys Based on the Al−Si−Cu and Al−Si−Cu−Mg Systems. Acta Materialia. 53: 3807-3819.
Birol, Y. 2009. Forming of AlSi8Cu3Fe Alloy in the Semi-solid state. Journal of Alloys and Compounds. 470: 183-187.
Shabestari, S. G. and Parshizfard E. 2011. Effect of Semi-Solid Forming on the Microstructure and Mechanical Properties of the Iron Containing Al−Si Alloys. Journal of Alloys and Compounds. 509: 7973-7978.
Chih-Ting, W., Sheng-Long, L., Meng-Hsiung, H. and Jing-Chie, L. 2010. Effects of Cu Content on Microstructure and Mechanical Properties of Al−14.5Si−0.5Mg Alloy. Materials characterization. 61: 1074-1079.
Cáceres, C. H., Svensson, I. L. and Taylor J. A. 2003. Strength-Ductility Behaviour of Al−Si−Cu−Mg Casting Alloys In T6 Temper. International Journal of Cast Metals Research. 15: 531-543.
Salleh, M. S, and Omar M. Z. 2015. Influence of Cu Content on Microstructure and Mechanical Properties of Thixoformed Al–Si–Cu–Mg Alloys. Transactions of Nonferrous Metals Society of China. 25(11): 3523-3538.
Campo, K. N., Proni, C. T. W., Zoqui, E. J. 2013. Influence of the Processing Route on the Microstructure of Aluminum Alloy A356 for Thixoforming. Material Characterization. 85: 26-37.
Anasyida, A. D., Daud, A. R. and Ghazali. M. J. 2010. Dry liding Wear Behaviour of Al-12Si-4Mg Alloy with Cerium Addition. Materials and Design. 31: 365-374.
Salleh, M. S., Omar, M. Z., Alhawari, K. S., Mohammed, M. N., Mad Ali, M. A., and Mohamad, E. 2016. Microstructural Evolution and Mechanical Properties of Thixoformed A319 Alloys Containing Variable Amounts of Magnesium. Transactions of Nonferrous Metals Society of China. 26(8): 2029-2042.
Downloads
Published
Issue
Section
License
Copyright of articles that appear in Jurnal Teknologi belongs exclusively to Penerbit Universiti Teknologi Malaysia (Penerbit UTM Press). This copyright covers the rights to reproduce the article, including reprints, electronic reproductions, or any other reproductions of similar nature.
