External Hard Particle Size Effect on Changes in Frictional Performance and Grit Embedment during Drag and Stop Mode Braking
DOI:
https://doi.org/10.11113/jt.v66.2700Keywords:
External hard particle, friction coefficients, particle size, grit embedmentAbstract
The effects of silica sand of 50-180 µm, 180-355 µm and 355-500 µm on friction performance and grit embedment at brake disc and pad interface was investigated. Results showed that present of external hard particles caused higher friction coefficient due to higher number of smaller particles involved in mixing and changing the effective contact, while good friction stability was attributed to smaller grit particles and compacted wear debris. Grit embedment was greatly dependent on presence of compacted wear debris as most grits were embedded into compacted wear debris with embedment of 0.8% was observed for 50-180 µm, 2% for 180-355 µm and 3% for 355-500 µm.
References
Eriksson, M., Bergman, F., Jacobson, S. 2002. On the Nature of Tribological Contact in Automotive Brakes. Wear. 252(1–2). 26–36.
Polak, A., Grzybek, J. 2005. The Method of Friction Mechanism Investigation in Automotive Disc Brake in the Presence of Hard Particle, Conference. Triboscience and Tribotechnology-Superior Friction and Wear Control in Engine and Transmission. 231–239.
Handa, Y., Kato, T. 1996. Effects of Cu Powder, BaSo4 and Cashew Dust on the Wear and Friction Characteristics of Automotive Brake Pads. Tribology Transactions. 39(2): 346–353.
Jang, H., Kim, S. J. 2000. The Effects of Antimony Trisulfide (Sb2S3) and Zirconium Silicate (ZrSiO4) in the automotive Brake Friction Material on Friction Characteristics. Wear. 239(2): 229–236.
Ostermeyer, G. P. and Muller, M. 2006. Dynamic Interaction of Friction and Surface Topography in Brake Systems. Tribology International. 39(5): 370–380.
Stachowiak, G. W., Batchelor, A. W. 1994. Engineering Tribology. 2nd ed. Butterworth Heinemann
Axen, N., Jacobson, S., Hogmark, S. 1994. Influence of Hardness of the Counterbody in Three-Body Abrasive Wear-An Overlooked Hardness Effect. Tribology International. 27(4): 233–241.
Cho, K. H., Jang, H., Hong, Y. S., Kim, S. J., Basch, R. H., Fash, J. W. 2008. The Size Effect of Zircon Particles on the Friction Characteristics of Brake Lining Materials. Wear. 264(3–4): 291–297.
Trezona, R. I., Allsopp, D. N., Hutchings, I. M. 1999. Transitions between Two-body and Three-body Abrasive Wear: Influence of Test Conditions in the Microscale Abrasive Wear Test. Wear. 225–229(Part 1) 205–214.
Syahrullail, S., Nakanishi, K., Kamitani, S. 2005. Investigation of the Effects of Frictional Constraint with Application of Palm Olein Oil Lubricant and Paraffin Mineral Oil Lubricant on Plastic Deformation by Plane Strain Extrusion. Journal of Japanese Society of Tribologists. 50(12): 877–885
Syahrullail, S., Kamitani, S., Nakanishi, K. 2012. Experimental Evaluation of Refined, Bleached, and Deodorized Palm Olein and Palm Stearin in Cold Extrusion of Aluminum A1050. Tribology Transactions, 55(2): 199–209.
Cho, M. H., Cho, K. H., Kim, S. J., Kim, D. H., Jang, H. 2005. The Role of Transfer Layers on Friction Characteristics in the Sliding Interface Between Friction Materials Against Gray Iron Brake Discs. Tribology Letters. 20(2).
Fischer, T. E., Singer, I. L., Pollock, H. M. 1992. Fundamentals of Friction - Macroscopic and Microscopic Processes. Dordrecht: Kluwer Academic Publishers. 299
Scieszka, S. F. 1980. Tribological Phenomena in Steel-composite Brake Material Friction Pairs. Wear. 64(2): 367–378.
Filip, P., Weiss, Z., Rafaja, D. 2002. On Friction Layer Formation in Polymer Matrix Composite Materials for Brake Applications. Wear. 252(3–4): 189–198
Rhee, S. K., Jacko, M. G., Tsang, P. H. 1990. The Role of Friction Film in Friction, Wear, and Noise of Automotive Brakes. SAE Technical Paper No. 900004 29–36.
Osterle, W., Griepentrog, M., Gross, T., Urban, I. 2001. Chemical and Microstructural Changes Induced by Friction and Wear of Brakes. Wear. 251(1–12): 1469–1476.
Osterle, W., Urban, I. 2004. Friction Layers and Friction Films on PMC Brake Pads. Wear. 257(1–2): 215–226.
Eriksson, M., Lord, J., Jacobson, S. 2001. Wear and Contact Conditions of Brake Pads: Dynamical In Situ Studies Of Pad On Glass. Wear. 249(3–4): 272–278.
Williams, J. A., Morris, J. H., Ball, A. 1997. The Effect of Transfer Layers on the Surface Contact and Wear of Carbon-Graphite Materials. Tribology International. 30(9): 663–676.
Jang, H., Lee, J. S., Fash, J. W. 2001. Compositional Effects of the Brake Friction Material on Creep Groan Phenomena. Wear. 251(1–12): 1477–1483.
Polak, A., Grzybek, J., Stolarski, B. 2005. Noise, Vibration and Harshness in Automotive Disc Brakes Related to the Presence of Hard Particles, Conference: Triboscience and Tribotechnology-Superior Friction and Wear Control in Eng. and Trans.
Abdul Hamid, M. K., Samion, S., and Stachowiak, G. W. 2012. Effects of Hard Particles on Friction Coefficients and Particle Embedment in Brake System during Hard Braking, AIP Conference Proceedings. 1440: 905–913.
Downloads
Published
Issue
Section
License
Copyright of articles that appear in Jurnal Teknologi belongs exclusively to Penerbit Universiti Teknologi Malaysia (Penerbit UTM Press). This copyright covers the rights to reproduce the article, including reprints, electronic reproductions, or any other reproductions of similar nature.
